Rapid Core Eject™ (RCE) Tarantula™ Hole Saws

Cut the toughest materials.

  • Tarantula hole saws cut the toughest materials up to 10x faster and make up to 50x more cuts than standard bi-metal hole saws
  • Cuts steel, stainless steel, wood with nails, plastics/PVC, non-ferrous metals, fiber cement board, fiberglass, mineral fiber, and more
  • Utilizes Spyder’s Rapid Core Eject Arbor System — rapidly eject the core (without prying), quickly change diameter, cut at an angle, and enlarge existing holes

sizes

7/8″

1″

1-1/16″

1-1/8″

1-1/4″

1-3/8″

1-1/2″

1-5/8″

1-3/4″

1-7/8″

2″

2-1/8″

2-1/4″

2-3/8″

2-1/2″

Tarantula™ Hole Saw

2-9/16″

2-5/8″

2-3/4″

3″

3-1/2″

3-5/8″

4″

4-1/4″

4-1/2″

RCE Tarantula™ features

Spyder’s carbide-tipped Tarantula hole saws cut the toughest materials including steel, stainless steel, nail-embedded wood, fiber cement board, plastics, and more. Durable tungsten carbide cutting teeth make up to 50x more cuts than conventional bi-metal hole saws, and they are up to 10x faster — cutting through the toughest materials and extending bit life. Use with Spyder’s Rapid Core Eject arbor system to remove cores without prying (drill hole, press button, pull back the hole saw, and eject the core), cut at an angle, and enlarge existing holes using two adapters on one pilot bit (adapters and pilot bit sold separately). Spyder TCT, Bi-Metal, and Tarantula hole saws fit on Spyder’s Rapid Core Eject arbor and pilot bits and on universal hole saw arbors. Using a drill motor with a support handle is recommended. Not for use in hammer mode or on harder, more abrasive materials.

  • Tarantula hole saws cut the toughest materials up to 10x faster and make up to 50x more cuts than standard bi-metal hole saws
  • Cuts steel, stainless steel, wood with nails, plastics/PVC, non-ferrous metals, fiber cement board, fiberglass, mineral fiber, and more
  • Utilizes Spyder’s Rapid Core Eject Arbor System — rapidly eject the core (without prying), quickly change diameter, cut at an angle, and enlarge existing holes
  • Tungsten carbide tipped hole saws for extended life, clean cuts and extreme material drilling versatility
  • Universal 1/2-20 thread uses Spyder Hex8 arbor/pilot bits or other universal hole saw arbors
  • 2-3/8-in depth of cut
  • Always use a drill motor with a support handle in standard rotary drilling mode only
  • Not for use in hammer drill mode or on harder abrasive materials

Watch it work

Warning

Hex-based pilot bits are intended to be used with a hex arbor adapter and hole saws. To minimize the risk of serious injury always use eye/respiratory protection and other PPE. Use the pilot bit and hole saw to drill only the materials listed on the product label. Make certain that the pilot bit is correctly sized for the hole saw being used. Always be sure that the drill bit protrudes above the saw teeth ¼” to 1” depending on the size of the saw. Follow RPM recommendations on the packaging for materials being cut and diameter of saw being used. Check the hole saw before use in the power tool – if excessive wear is present, the saw is bent, teeth are fractured or damaged, replace saw before use. Use a drill motor that is equipped with a support handle and start drilling with a light forward pressure. Important instructions and warnings are contained in the tool owner’s manual – please refer to the power tool owner’s manual before using the tool with this tool. Failure to heed all safety instructions, warnings, and in-use recommendations by the power tool manufacturer regarding the use of the reciprocating saw and blade could result in serious bodily injury.

WARNING
HOLE SAWS ARE NOT TO BE USED IN HAMMER OR IMPACT MODE – only drill in standard rotary drilling mode or saw may become damaged/broken and may increase the likelihood of user injury.