1-5/8″ Tarantula™ Hole Saw
- Tarantula™ hole saws cut the toughest materials up to 10x faster and make up to 50x more cuts than standard bi-metal hole saws
- Cuts steel, stainless steel, wood with nails, plastics/PVC, non-ferrous metals, fiber cement board, fiberglass, mineral fiber, and more
- Utilizes Spyder’s Rapid Core Eject Arbor™ System — rapidly eject the core (without prying), quickly change diameter, cut at an angle, and enlarge existing holes
Spyder’s carbide-tipped Tarantula™ hole saws cut the toughest materials including steel, stainless steel, nail-embedded wood, fiber cement board, plastics, and more. Durable tungsten carbide cutting teeth make up to 50x more cuts than conventional bi-metal hole saws, and they are up to 10x faster — cutting through the toughest materials and extending bit life. Use with Spyder’s Rapid Core Eject™ arbor system to remove cores without prying (drill hole, press button, pull back the hole saw, and eject the core), cut at an angle, and enlarge existing holes using two adapters on one pilot bit (adapters and pilot bit sold separately). Spyder TCT, Bi-Metal, and Tarantula™ hole saws fit on Spyder’s Rapid Core Eject™ arbor and pilot bits and on universal hole saw arbors. Using a drill motor with a support handle is recommended. Not for use in hammer mode or on harder, more abrasive materials.
- Up to 50x more cuts than bi-metal hole saws
- Up to 10x faster than standard hole saws
- Carbide tipped for extended life in tough materials
- Cuts nail-embedded wood, steel, stainless steel, plastics, non-ferrous metals, fiber cement board and more
- Up to 2-3/8″ Depth of Cut
- Utilizes Rapid Core Eject™ Arbor System – rapidly eject the core, quickly change diameter, cut at an angle, and enlarge existing holes
- Always use a drill motor with a support handle in standard rotary drilling mode only
- Not for use in hammer drill mode or on harder abrasive materials
Arbor Hex Size:
Watch it Work
To reduce the risk of injury, read the instruction manual and follow the safety regulations of the power tool you will be using with your Spyder accessory. Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, protective apparel and hearing protection should be used in appropriate conditions to reduce the risk of personal injury. WARNING: Operating the tool without wearing proper protection may result in serious injury. To reduce the risk of explosion, electric shock, and property damage, always check the work area for hidden gas pipes, electrical wires, and water pipes when making blind and/or plunge cuts. Before each use, check that the hole saw is free from damage and excessive wear. Discard hole saw if damage is noticed or suspected as this can cause excessive friction, saw binding, kickback, create dangerous flying debris and/or create other unsafe situations that may cause injury. Hex-based pilot bits are intended to be used with hex-based arbor adapters and hole saws. Use a pilot bit which is correctly sized for the hole saw being used. Always be sure that the pilot bit extends beyond the cutting edge of the saw by at least ¼”; for deep cut hole saws, the pilot bit should extend at least 1” beyond the cutting edge of the saw. Follow the recommended operating speed for the saw size and the material being cut. Use the proper pilot bit and hole saw for your material. Only drill materials that are listed on the product label. Use a drill motor that is equipped with a support handle. Start cutting with a light forward pressure. For cuts that are square to the surface, start the cutting process with the saw square to the material being cut so all teeth begin to cut at the same time. This will help prevent premature wear and damage to the saw. Feeding the saw in and out or using a slight circular rocking motion may assist in clearing material shavings from the hole being cut. When sawing in wood, finish the hole from the opposite side to prevent splintering. Once the pilot bit has broken through the other side, you can use this hole to guarantee you are in line with where you have already started cutting.
HOLE SAWS ARE NOT TO BE USED IN HAMMER OR IMPACT MODE! Only drill in standard rotary drilling mode. Drilling in hammer or impact mode can cause the hole saw to become damaged/broken and can increase the likelihood of user injury due to dangerous flying debris or other unsafe situations.