Rapid Core Eject™ (RCE) tungsten carbide tipped (TCT) hole saws

Extreme Material Versatility and Faster Cuts.

  • 10x more cuts and 5x faster than standard bi-metal hole saws
  • Spyder’s Rapid Core Eject arbor system ejects cores without prying, quickly changes diameter, cuts at an angle, and enlarges existing holes
  • Drill wood, MDF, plywood, fiber cement board, porous concrete block, some brick, ceramic wall tile, plastic, PVC and more

Sizes

3/4″

7/8″

1″

1-1/8″

1-1/4″

1-3/8″

1-1/2″

1-5/8″

1-3/4

1-7/8″

2″

2-1/8″

2-1/4″

2-3/8″

2-1/2″

2-9/16″

2-5/8″

2-3/4″

Tungsten Carbide Hole Saw

3″

3-1/4″

3-1/2″

3-5/8″

3-3/4″

4″

4-1/8″

4-1/4″

4-1/2″

4-5/8″

4-3/4″

5″

5-1/2″

5-3/4″

6″

6-1/4″

6-3/8″

6-5/8″

RCE TCT features

Spyder’s Tungsten Carbide-Tipped (TCT) hole saws cut more materials up to 5x faster and make up to 10x more cuts — lasting longer than conventional bi-metal hole saws. TCT hole saws drill through wood, MDF, fiber cement board, porous concrete block, ceramic wall tile, plastic/PVS and more. Use with Spyder’s Rapid Core Eject arbor system to remove cores without prying (drill hole, press button, pull back the hole saw, and eject the core), cut at an angle, and enlarge existing holes using two adapters on one pilot bit . All TCT, Tarantula, and Bi-Metal hole saws fit on Spyder Rapid Core Eject arbors and pilot bits (sold separately), and on universal hole saw arbors. Spyder’s TCT hole saw is the pro’s choice for innovation, high performance, speed, and versatility — drill more holes in more materials in less time. Not for use in hammer mode, or for drilling metal, wood with nails, harder, abrasive materials, or block/brick/tile applications with a Mohs hardness of 6 or greater. Always use a drill with a support handle.

  • 10x more cuts and 5x faster than standard bi-metal hole saws
  • Spyder’s Rapid Core Eject arbor system ejects cores without prying, quickly changes diameter, cuts at an angle, and enlarges existing holes
  • Drill wood, MDF, plywood, fiber cement board, porous concrete block, some brick, ceramic wall tile, plastic, PVC and more
  • Tungsten carbide tipped for extended life, clean cuts and extreme material drilling versatility
  • Maximum cut depth of 2-3/8-in
  • Universal 5/8-18 thread uses Spyder Hex10 arbor/pilot bits or other universal hole saw arbors
  • Not for drilling metal, wood with nails, or in block/brick/tile applications with a Mohs hardness of 6 or greater
  • Always use a drill motor with a support handle
  • Not for use in hammer mode

Watch it work

Warning

Hex-based pilot bits are intended to be used with a hex arbor adapter and hole saws. To minimize the risk of serious injury always use eye/respiratory protection and other PPE. Use the pilot bit and hole saw to drill only the materials listed on the product label. Make certain that the pilot bit is correctly sized for the hole saw being used. Always be sure that the drill bit protrudes above the saw teeth ¼” to 1” depending on the size of the saw. Follow RPM recommendations on the packaging for materials being cut and diameter of saw being used. Check the hole saw before use in the power tool – if excessive wear is present, the saw is bent, teeth are fractured or damaged, replace saw before use. Use a drill motor that is equipped with a support handle and start drilling with a light forward pressure. Important instructions and warnings are contained in the tool owner’s manual – please refer to the power tool owner’s manual before using the tool with this tool. Failure to heed all safety instructions, warnings, and in-use recommendations by the power tool manufacturer regarding the use of the reciprocating saw and blade could result in serious bodily injury.

WARNING
HOLE SAWS ARE NOT TO BE USED IN HAMMER OR IMPACT MODE – only drill in standard rotary drilling mode or saw may become damaged/broken and may increase the likelihood of user injury.