Kit de scies cloches à pointe en carbure de tungstène (TCT) Rapid Core Eject™ 18 pièces

Kit de scies cloches à pointe en carbure de tungstène (TCT) Rapid Core Eject™ 18 pièces

SKU: 600938

Diamètre(s) de la scie : 3/4, 7/8, 1-1/8, 1-3/8, 1-3/4, 2, 2-1/2, 2-5/8, 3, 3-5/8, 4-1/8, 4-1/2 pouces -
Jusqu'à 10 fois plus de coupes et jusqu'à 5 fois plus rapide que les scies cloches bimétalliques standard -
Le système d'arbre Rapid Core Eject™ de Spyder éjecte les noyaux sans forcer, change rapidement le diamètre, coupe en biais et agrandit les trous existants -
Percer du bois, du MDF, du contreplaqué, des panneaux de fibrociment, des blocs de béton poreux, certaines briques, des carreaux muraux en céramique, du plastique, du PVC et plus encore -
Pointe en carbure de tungstène pour une durée de vie prolongée, des coupes nettes et une polyvalence extrême de perçage des matériaux -
Le filetage universel utilise des forets Spyder/pilotes ou d'autres mandrins de scie cloche universels -
Profondeur de coupe maximale de 2-3/8 po -
Ne convient pas au perçage du métal, du bois avec des clous ou dans des applications sur blocs/briques/tuiles avec une dureté Mohs de 6 ou plus -
Utilisez toujours un moteur de perceuse avec une poignée de support en mode de perçage rotatif standard uniquement -

Product Details

Spyder’s Tungsten Carbide-Tipped (TCT) hole saws cut more materials up to 5x faster and make up to 10x more cuts — lasting longer than conventional bi-metal hole saws. TCT hole saws drill through wood, MDF, fiber cement board, porous concrete block, ceramic wall tile, plastic/PVC and more. Use with Spyder’s Rapid Core Eject™ arbor system to remove cores without prying (drill hole, press button, pull back the hole saw, and eject the core), cut at an angle, and enlarge existing holes using two adapters on one pilot bit. All TCT, Tarantula, and Bi-Metal hole saws fit on Spyder Rapid Core Eject™ arbors and pilot bits (sold separately), and on universal hole saw arbors. Spyder’s TCT hole saw is the pro’s choice for innovation, high performance, speed, and versatility — drill more holes in more materials in less time. Not for use in hammer mode, or for drilling metal, wood with nails, harder, abrasive materials, or block/brick/tile applications with a Mohs hardness of 6 or greater. Always use a drill with a support handle.

Why Choose Spyder Rapid Core Eject™

Saw Diameter(s): 3/4, 7/8, 1-1/8, 1-3/8, 1-3/4, 2, 2-1/2, 2-5/8, 3, 3-5/8, 4-1/8, 4-1/2-Inch

Up to 10x more cuts and up to 5x faster than standard bi-metal hole saws

Spyder’s Rapid Core Eject™ arbor system ejects cores without prying, quickly changes diameter, cuts at an angle, and enlarges existing holes

Drill wood, MDF, plywood, fiber cement board, porous concrete block, some brick, ceramic wall tile, plastic, PVC and more

Tungsten carbide tipped for extended life, clean cuts and extreme material drilling versatility

Universal thread uses Spyder arbor/pilot bits or other universal hole saw arbors

Maximum cut depth of 2-3/8-in

Not for drilling metal, wood with nails, or in block/brick/tile applications with a Mohs hardness of 6 or greater

To reduce the risk of injury:

Read the instruction manual and follow the safety regulations of the power tool you will be using with your Spyder accessory.

Use personal protective equipment. Always wear eye protection.

Protective equipment such as a dust mask, non-skid safety shoes, protective apparel and hearing protection should be used in appropriate conditions to reduce the risk of personal injury.

WARNING:

Operating the tool without wearing proper protection may result in serious injury.

Do not use near flammable materials or gases!

To reduce the risk of explosion, electric shock, and property damage, always check the work area for hidden gas pipes, electrical wires, and water pipes when making blind and/or plunge cuts.

Before each use:

Check that the hole saw is free from damage and excessive wear. Discard hole saw if damage is noticed or suspected as this can cause excessive friction, saw binding, kickback, create dangerous flying debris and/or create other unsafe situations that may cause injury.

Use a pilot bit which is correctly sized for the hole saw being used.

Hex-based pilot bits are intended to be used with hex-based arbor adapters and hole saws. Use a pilot bit which is correctly sized for the hole saw being used. Always be sure that the pilot bit extends
beyond the cutting edge of the saw by at least ¼”; for deep cut hole saws, the pilot bitshould extend at least 1” beyond the cutting edge of the saw.

WARNING: Hole saws are not to be used in hammer or impact mode!

Only drill in standard rotary drilling mode. Drilling in hammer or impact mode can cause the hole saw to become damaged/broken and can increase the likelihood of user injury due to dangerous flying debris or other unsafe situations.
For TCT saws recommended for use on concrete products, brick, or tile materials, check the Mohs hardness of the material to be drilled. Materials like poured concrete, some brick/block, floor tile, ceramic tile, porcelain, and others, may have a Mohs hardness of higher than 6. The TCT hole saw is not recommended for use in materials with a Mohs hardness of higher than 6.

To reduce the risk of injury:

Read the Spyder Hole Saw RPM Chart for the recommended operating speed for the saw size and the material being cut.
Use the proper pilot bit and hole saw for your material. Only drill materials that are listed on the product label.
Use a drill motor that is equipped with a support handle.
Start cutting with a light forward pressure. For cuts that are square to the surface, start the cutting process with the saw square to the material being cutso all teeth begin to cut at the same time. This will help prevent premature wear and damage to the saw. Feeding the saw in and out or using a slight circular rocking motion may assist in clearing material shavings from the hole being cut. When sawing in wood, finish the hole from the opposite side to prevent splintering. Once the pilot bit has broken through the other side, you can use this hole to guarantee you are in line with where you have already started cutting.

Included in Set

Scie cloche sans arbre Rapid Core Eject™ en carbure de tungstène 3/4" à pointe en carbure de tungstène (TCT)