HOLE SAWS & ARBORS

[ HOLE SAWS & ARBORS ]

Hole saws with a patented arbor system, allowing you to eject cores from Spyder® TCT and Bi-Metal hole saws at the push of a button.

  Features

  • Built for speed
    Our Tungsten Carbide hole saws are 5X faster and 10x times more cuts than bimetal hole saws.
  • Cut at an angle
    Click and pull the hole saw back to extend the pilot drill’s length enough to cut at an angle. Release to complete the hole.
  • Enlarge holes that were drilled too small
    Use your hole saw as a guide to turn a small-diameter hole into a larger one by using a wider diameter saw.
  • Drop out the core
    Simply push the button and slide the blade back to remove the core using our patented arbor system.
  • Download the PDF to see full details of our TCT, Bi-Metal HSS and HSS+ saws, as well as our pilot drills.

Watch it work

"I'm a master plumber, business owner and have 17 years experience in the field. I've used a lot of different bits ... I was skeptical of the Spyder brand because it seemed gimmicky. But I bought it in a jam because I was outfitting a new vehicle for my business and needed something asap. Wasn't expecting much and was very, very pleased. Quick cutting through wood and super quick ejecting of the cut material. Would recommend."

- MLC

"I've been in business almost 19 years and I have to say these are the best hole saws on the market. I wish I would have found out about them sooner!"

- Carpenter57

"Pretty amazed as it cuts through anything I ask it to, including cement siding. Puts a smile on my face every time I use it."

- Frank

"Compared to a Milwaukee and Lenox (of which I have both), you can eject the plug in just 1 second with the push of a button and sliding the saw up the arbor. It takes me a minute usually and a screwdriver to remove the plug from the other two. Highly recommended."

- Wilmo

"I really, really love the ability to stack the bits so you can enlarge a previously drilled out hole. Its ingenious and has saved me tons of headaches and time."

- BobbyCa

Instructions & Warnings

INSTRUCTIONS:
INSTALL A HOLE SAW CUP

1) Retract the spring-loaded pin plate and screw the hole saw onto the threaded insert end of the arbor.
2) Align the pin holes in the saw cup to the arbor pin locations and release the pin plate.
3) Push the button and slide the cup assembly back towards the drill.
4) Release button and slide cup assembly forward until it latches in place.

DROP OUT THE CORE

1) Push the button.
2) Slide the hole saw assembly back toward the drill.
3) Pull the core free of the arbor, if necessary.

CUT AT AN ANGLE

1) Slide the hole saw assembly back against the drill chuck, leaving the maximum length of the drill bit
exposed.
2) Drill a pilot hole in the center of the area you want to cut.
3) Continue to drill until the edge of the saw cup has made a small cut in the substrate.
4) Stop the drill and remove the bit from the substrate. Slide the cup assembly down the arbor until it
latches in place.
5) Reposition the bit into the pilot hole and locate the saw teeth into the slot created previously.
6) Start the drill and continue cutting the angled hole.

ENLARGE EXISTING HOLES

1) Detach the smaller hole saw blade that you just used to create the hole in the substrate.
2) Choose a larger hole saw cup and attach it to the arbor.
3) Attach another arbor to your original hole saw cup and slide the smaller saw cup inside the larger cup
assembly and onto the hex bar.
4) Insert the smaller hole saw cup into the hole you drilled previously.
5) Enlarge the hole, using the inner hole saw cup to center the blade.

Additional arbors sold separately.

PILOT BIT/COMPLETE ARBOR SYSTEM WARNING

This pilot bit is intended to be used with hole saws. To minimize the risk of serious injury always use eye protection and use the pilot bit only on the products listed on the front of this label for which this pilot bit is designated to minimize the risk that the pilot bit will break and injure you during use. Make certain that the pilot bit is correctly sized for the hole saw being used. Always be sure that the drill bit protrudes above the saw teeth ¼” to 1″ depending on the size of the saw. Start the drill at low speed with the bit contacting the substrate. Read all warnings provided by the drill manufacturer before using this product.

HOLE SAW WARNING

To minimize the risk of serious injury, always use eye protection and gloves. Use the hole saw only on the products listed on the front of this label for which this hole is designated, to minimize the risk that the hole saw will shatter or break and injure you during use. Inspect the hole saw prior to each use and replace with a new one if damaged, bent, cracked or if any of the tips are missing. Always follow the safety instructions in your power tool instruction manual.

Spyder Arbors and Pilot Bits WARNING

This pilot bit is intended to be used with hole saws. To minimize the risk of serious injury, always use eye protection and use the pilot bit only on the products listed on the front of this label for which this pilot bit is designated to minimize the risk that the pilot bit will break and injure you during use. Make certain that the pilot bit is correctly sized for the hole saw being used. Always be sure that the drill bit protrudes above the saw teeth ¼” to 1″ depending on the size of the saw. Start the drill at low speed with the bit contacting the substrate. Read all warnings provided by the drill manufacturer before using this product.

BIMETAL HOLE saw
Recommended RPM

Bimetal hole saw RPM

 

TCT Hole Saw
Recommended RPM

TCT Hole Saw RPM